Digitize and optimize preventive maintenance for process instrumentation

Defining scope, optimizing tasks, and using digitalization
Special Section May/June main img

By Fawaz AlSahan, CAP, SCE

Maintenance can be made more efficient, helping make operations more efficient and profitable, by leveraging new digital technologies. Conventional time-based preventive maintenance (PM) is widely used throughout industry but has shortcomings that can be overcome with smart sensors and analytics (digital transformation). This enables process facilities to move into performance-based and shutdown-based preventive maintenance.

The common categories for preventive maintenance are:

  • Time-based preventive maintenance: Conducted as a defined procedure during a preset interval.
  • Performance-based preventive maintenance: Conducted when the instrument performance goes below a certain limit. Performance monitoring is done either online (via an online instrument) or off-line (via a portable instrument).
  • Shutdown-based preventive  maintenance: Conducted during plant shutdown.

The diagram shows the ISO categorization for maintenance in general and preventive maintenance in particular.

It is worth highlighting that conventional time-based preventive maintenance is widely used and has the following shortcomings:

  • Forty to 60 percent of PM tasks add no value to operations.
  • Some PM tasks are similar.
  • Many tasks require removing the instruments or valve to the shop, while condition monitoring is enough to determine reliability.
  • New technologies and digital instrument features are not used to optimize tasks.
  • Some PM tasks have a high probability of causing unnecessary shutdowns and operation interruptions.

Using smart sensors and analytics (digital transformation) resolves these shortcomings and enables process facilities to move into performance-based and shutdown-based preventive maintenance.

Defining PM scope, tools, and frequency

To have the right preventive maintenance for instrumentation, first clearly define the type and scope of PM. Proper tools need to be selected, and the right frequency defined. The scope of PM can include a certain task to be performed. This can be a time-based visual check, time-based functionality check, removal and overhauling, or a condition-based task.

Second, address who will perform the PM task, such as a field operator or maintenance technician. Determining this point requires agreement between the parties, with clear tasks and a system to collect and communicate the findings.

The tools used for PM tasks are either instrument asset management systems (IAMSs), hand-held tools, an instrument built-in keypad, hand tools, or shop activities. The frequency of a PM task is based on prior knowledge from similar equipment, manufacturer or supplier data, reliability data, and performance prediction, and defines the task as online or shutdown activity.

Strategies to optimize PM

Optimizing the preventive maintenance for instrumentation is needed to eliminate unnecessary activities and unnecessary cost. Excessive preventive maintenance may also cause nuisance trips or operation upset. This is another motive to optimize the PM tasks.

Implement optimization with the following strategies: improve the design and apply technologies, capitalize on instrumentation self-diagnostics and online condition monitoring, and use the redundancy approach, once justifiable.

Design and technology

Nowadays, available technologies, like smart sensors, bring a new dimension of reliability and minimize maintenance requirements. Capitalizing on the following technologies and design approach will highly reduce the PM scope and time:

  • single-rod, guided-wave radar (GWR) for level measurement
  • pressure transmitters instead of process-actuated switches
  • smart pressure and vibration fork switches (with display and/or diagnostics) instead of conventional blind switches
  • diaphragm/remote seal pressure transmitters instead of tubing-based transmitters
  • digital vibration transmitter/switch instead of mechanical switches
  • smart valve
    positioner
  • single-rod GWR and two-wire noncontact radar for inventory tanks application
  • electrochemical gas detector for H2S gas detection
  • infrared gas detector for combustible gas detection
  • configuring a discrepancy alarm between adjacent control and safety transmitters
  • avoiding soft-seated control valves and instead installing a metal-seated control valve next to a tight shutoff rotary isolation valve

Diagnostics and online condition monitoring

Available instruments are now smart and have internal diagnostics (analytics) and digital communication. These features are effectively used to improve the preventive maintenance program and eliminate or highly reduce traditional practices. Diagnostic data is obtained and collected using:

  • smart sensors (like smart transmitters, smart positioners, and smart pressure switches)
  • an analytics data platform (IAMS, which receives the data from the smart instruments via a wired or wireless connection and generates a status message with a recommendation)
  • digital connectivity, like Foundation fieldbus (FF) with physical layer diagnostics


Special Section May/June fig 1
Figure 1. Maintenance categorization

Source: ISO 14224:2016


Redundancy

Redundancy is having a permanent or temporary reference to compare the installed instrument performance and reading to. Below are some examples:

  • having dual circuits (or more) for axial and radial vibration, bearing temperature, and fired equipment flame monitoring
  • applying two-out-of-two voting, if safe and practical, to avoid nuisance trips and reduce excessive maintenance
  • installing control and shutdown transmitters with the same calibration range and configuring discrepancy alarms for them
  • having permanently or temporarily installed pressure gauges to compare to the nearby pressure transmitters' readings
  • local level gauges (sight glass, magnetic level indicator) or infrared cameras to cross check the level instruments' (displacer, differential pressure, radar, etc.) readings
  • checking the online temperature sensor reading with a temperature gauge, a test temperature element, a portable temperature detector, or with an infrared detector/camera.

SIS preventive maintenance

Diagnostics provided by the logic solver, input devices (like transmitters), and output devices (like emergency isolation valves) should support the overall preventive maintenance program for the safety instrumented system (SIS) by reducing the required physical preventive maintenance. The safety requirement specification (SRS) document should be developed after the safety integrity level (SIL) study/verification is conducted. The SRS specifies the required testing intervals for the SIS equipment (logic solver, input and output devices).

To define and further optimize the required preventive maintenance for SIS devices, do the following for each safety instrumented function (SIF):

  • Review the SIL study and SIL verification report or conduct a study.
  • Check the test interval (TI) for input and output devices recommended in the study report.
  • Increase the TI to the maximum number (such as matching the plant total shutdown interval) and confirm if the SIL requirement is still achieved. The preventive maintenance interval is based on the maximum possible TI.
  • For emergency isolation valves, if  the TI for these valves (i.e., full stroke test) cannot meet the plant shutdown window, introduce partial stroke testing (PST) with a weight of 60 percent of the total stoke test. TI for the total and partial valve stroke shall then be clearly defined.


Special Section May/June fig 2
Figure 2. Probability of failure on demand calculation and safety integrity level.



Operator tasks versus technician tasks

There should be two different PM tasks. One is conducted by the maintenance crew, and one is conducted by the operation crew. Operation tasks are visual checks, visual inspections, or simple test and observation tasks. The maintenance crew PM tasks include detailed test procedures, calibration, and physical testing that requires hand tools and communication devices.

The objective of segregating the operation and maintenance tasks is to optimize the testing intervals and duration. Some tasks are simple, requiring a long time to prepare the work permit and the system that needs PM. Also, due to the internal mandatory requirements, the operations team must be involved in these PM tasks. Simple examples are stroke testing for control valves and emergency isolation valves and testing gas detectors.

Analysis of PM findings

There is great value in reviewing and analyzing PM findings in terms of preventing failures and maintaining equipment reliability and availability. This requirement is clearly addressed in industry references (figure 3). Doing analysis requires the PM executer to write accurate PM findings. The analysis of the compiled findings helps identify the PM tasks that add value and eliminate the "value-wasting" PM tasks. Also, it helps to identify repeated failures and to recommend revisiting some system designs. Moreover, analyzing PM findings helps improve PM tasks by better managing spare parts, highlighting optimization opportunities and life-cycle costs, and capturing and applying lessons learned across the plant or company.



Special Section May/June fig 3
Figure 3. Maintenance work order

Source: EN 13460


Impact on instrumentation preventive maintenance

Digital transformation will change the world of preventive maintenance for instrumentation and equipment to more "predictive analytics," where data is used to predict performance and failures. The "big data" collected from the instruments can be used for making decisions about when maintenance is actually needed. Hence, 70 percent or more of conventional PM tasks for both process instrumentation and equipment could be deleted. Digital transformation will address the major maintenance challenges of aging equipment and the aging workforce, and can highly cut cost, time, and manpower.

Solutions like wireless instruments, automatic work permits, risk-based maintenance, remote maintenance, robotics, and self-calibrating instruments will be used more and more. Printed PM sheets for equipment and instruments will be replaced by additional smart sensors, like acoustic detectors, video, and infrared cameras. Digital transformation can also extend monitoring into the instrumentation utilities (i.e., the quality of instrument air and power supply).

Digital transformation will also provide more efficient and safer PM by remote condition monitoring and built-in analytics and can provide faster resolutions to problems by having more data and more efficient spare parts management.

Control valves are another beneficiary of digitalization, where the cloud can be used to obtain data from the field, predict the life and performance, and also estimate the time for overhaul. Video and augmented reality, used to monitor and train the maintenance crew on valve maintenance, will be part of this digital transformation.

PM procedures for process instrumentation

This section highlights recommended PM tasks for common instruments. It covers SIS input and output devices, control valves, motor operated valves (MOV), transmitters, gas and flame detectors, thermowells, process flowmeters, flare flowmeters, process actuated switches, level gauges, vibration circuits, and skids instruments.

An analytical approach

This article gave guidelines for digitizing and optimizing the instrumentation PM program, an important task that every company needs to perform to avoid an unnecessary maintenance work load, eliminate operational losses, cut unnecessary costs, and digitally transform conventional PM into analytical maintenance. The scope of this exercise included revisiting the instrument type, PM scope, PM frequency, the PM task performer, and the task sheet.

Using smart sensors and analytics (digital transformation) lets process facilities move into performance-based and shutdown-based preventive maintenance. They eliminate or greatly reduce the conventional preventive maintenance for instrumentation, and replace it with an analytical approach, which uses data to monitor the instrument performance and predict failures.

Recommended preventive maintenance for process instrumentation
Special Section May/June fig 4
Special Section May/June fig 5
Special Section May/June fig 6

 
 subscribe now jpeg

Fast Forward

  • Preventive maintenance for instrumentation shall be redefined as periodical, online, or shutdown tasks.
  • Achieve PM optimization by enhancing the design, effectively using instruments’ built-in diagnostics, and utilizing new or alternative technologies.
  • Digital transformation can eliminate or greatly reduce conventional preventive maintenance for instrumentation.
 

About the Author

Fawaz AlSahan, CAP, SCE is the chairman of Saudi Aramco instrumentation standards, a member of the Saudi Arabia Standards Committee of Electrical Metrology, and a voting member of ISO technical committees. AlSahan has more than 20 years of experience in design, technical support, and maintenance of instrumentation and automation systems. He has several published papers, teaches several courses, and holds several patents.

New instrumentation products

Gas analyzer for hazardous area zones I and II

To use and valorize natural gas, it is necessary to control its composition. Even if it is composed mainly of methane, natural gas contains some traces of sulfur compounds that can affect its quality and lead to pipe corrosion during transport. Therefore, companies that work with natural gas want to control the level of sulfur compound impurities as well as add specific Mercaptans to odorize the gas and make it easily detectable.

The energyMEDOR measures with speciation the following sulfur compounds generally present in the natural gas: H2S, DMS, DMDS, and Mercaptans. This instrument works in hazardous areas, such as ATEX zone 1 without any purge gas requested for operation.

The MEDOR Ex d uses MEDOR wet cell detector technology to analyze these sulfur compounds in hazardous areas without purge gas. The instrument needs only a very small amount of zero air or nitrogen to operate (down to 4 mL/min), and the wet cell Sulfur Specific Detector detects sulfurs as low as 1 ppb. This certified analyzer can operate in zone I and II and can be used with 230V, 115V, and 24V DC power supplies.
Chromatotec, www.chromatotec.com

Point level switch

The Nivector FTI26 point level switch detects all types of powdered and fine-grained solids, such as plastic granules, detergent, grain, sugar, and other dry materials. The switch can be installed at the top of a tank to indicate high level, or at the bottom of a tank to indicate low level. The switch is a capacitance device that fulfills all hygienic requirements, such as 3A, EHEDG, and FDA. It is cleanable up to protection class IP69. No additional or individual adjustments to different media are necessary. The function of the switch can be checked via LED signalization without dismounting the device.
Endress+Hauser, www.us.endress.com

Two-wire loop-powered Coriolis transmitter

The Micro Motion 4200 two-wire loop-powered Coriolis transmitter can replace existing two-wire flow devices. The device can accommodate a line size of 4 inches and has an onboard real-time clock for diagnostics. The unit is available in a remote-mount option for applications that require the transmitter to be located separately from the sensor. The 4200 transmitter provides a viable migration path where Coriolis meters were previously not practical as a two-wire solution.
Emerson, www.emerson.com

 

Reader Feedback

We want to hear from you! Please send us your comments and questions about this topic to InTechmagazine@isa.org.