Machine automation basics

Systems must integrate multiple power and control subsystems and components into a coherent whole Factory Auto Mar/Apr Main Img

By Chip McDaniel

Faced with ever-increasing cost pressures and demands for improved performance, machine builders are actively seeking new automation solutions with improved cost/performance ratios. In response to these demands, vendors must often incorporate commercial off-the-shelf components and other technologies to deliver more performance at lower costs in smaller form factors.

This article shows how machine builders and vendors can work together to deliver the automation systems demanded, and how to successfully integrate the multiple power and control subsystems and components.

Components and subsystems

A machine's automation system primarily consists of power and control components. For a smaller machine, these may be housed in one panel (figure 1); whereas larger machines may require multiple panels, often one for control and another for power. The main subsystems and components of a machine automation system are:

  • power distribution
  • motor control and drives
  • safety system
  • programmable controllers
  • discrete and analog I/O
  • communication systems
  • human-machine interface (HMI)

The power distribution subsystem feeds power to components, such as motors, drives, and controllers. The control subsystem primarily consists of safety systems, programmable controllers, discrete and analog I/O, communication systems, and HMIs. Let's look at each of these areas in more detail.



Factory Auto Mar/Apr fig 1
Figure 1. For smaller machines, a single panel is often used to house both the power distribution system and the control components.



Power distribution

The National Electric Code (NEC, also NFPA 70) has much to say about using electricity properly to safeguard persons and property. The code comes into play well before the power source connects to the machine control enclosure through a plug, disconnect, or terminal block. At the machine, the NFPA 79: Electrical Standard for Industrial Machinery is the benchmark for industrial machine safety related to fire and electrical hazards. Some of the major requirements in machine control power distribution discussed in these standards include using proper disconnect means, protecting personnel from contact with electrical hazards, and protecting equipment from overcurrent and overloads.

The disconnect—whether a switch, circuit breaker, or cord with a plug—must be provided for any control enclosure fed with voltages of 50 VAC or more. It should be properly sized, positioned, wired, labeled, and, in some cases, interlocked to the enclosure door.

Protecting personnel from contact with electrical hazards is always needed, both inside and outside a machine power or control panel. All conductors must be protected from contact by personnel. Most power distribution devices are designed to facilitate this level of protection, but live components, such as power buses, distribution blocks, and other power terminals, should be covered with a nonconductive, see-through cover.

Protecting equipment from overcurrent is critical to reduce the chance of fire. Conductors and electrical components must be protected from overcurrent related to short circuits. Overcurrent protection devices, such as fuses and circuit breakers, must be sized based on conductor current-carrying capacity, device interrupt rating, maximum fault current, system voltage, load characteristics, and other factors.

For power circuits, branch-circuit-rated devices must be used to meet current-limiting and ground fault protection requirements. Supplemental overcurrent protective devices are not suitable for use in these circuits but work well in downstream control circuits tapped from the load side of the branch circuit.

Motor control and drives

Motors have special needs in machine control. For every motor, a proper form of electrical control is required, from simple on/off to more complex variable speed applications. Motor control devices include manual motor starters, motor contactors and starters with overloads (figure 2), drives, and soft starters.

A motor circuit must include both overcurrent (short circuit) and overload protection. This typically consists of branch-circuit protection, such as properly rated fuses, and a motor starter with overload protection devices, such as thermal overloads, but additional protection may be needed.

Additional protection to consider for machine control components includes loss of cooling and abnormal temperatures. Ground fault protection is also needed, so a proper ground connection is important. Over, under, and loss of voltage must also be considered. Protection from lightning, overspeed, and loss of a voltage phase in three-phase supplies are additional considerations for proper machine control.

Some motor controllers, such as drives and combination controllers, are self-protected. If this is the case, the device's rating or manufacturer's instructions will clearly note it is suitable for output conductor protection.




Factory Auto Mar/Apr fig 2
Figure 2. These Fuji manual motor starters and contactors from AutomationDirect have high switching capacity and integrate the functions of a molded case circuit breaker and a thermal overload relay.



Safety system

A risk assessment drives the safety system design as needed to remove motion-causing energy, including electrical and fluid power, to safely stop the equipment for protection of both personnel and machines. Many safety standards come into play for proper machine control at both a mechanical and electrical level. Proper mechanical machine guarding and access points, as well as elimination of identified hazards, is a starting point. Safety relays or safety-rated controllers must be used to monitor safety switches, safety limit switches, light curtains, and safety mats and edges.

In small machine control applications, a safety relay is probably the simplest way to integrate safety functionality for emergency stop, monitoring a guard door, or protecting an operator reaching through a light curtain. In more advanced machines, safety-rated controllers provide the same functions, but can simplify the integration of multiple safety devices. Safety-rated controllers reduce hardwired safety logic by providing a platform to program the safety functions needed for proper and safe machine control.

Programmable controllers and I/O

Available in form factors from small to large, the machine controller can be a programmable logic controller (PLC), a programmable automation controller (PAC), or a PC. The complexity of the machine control application, end-user specifications, and personal preference drive controller selection. Many vendors have families of controllers to cover a range of applications from simple to complex, allowing a machine builder to standardize to some extent. Often three or more physical configurations-small, medium, and large form factors-are available from the controller manufacturer.

Using the same software platform to program a family of controllers is becoming the norm. This allows the designer to first program the system, and then select the right controller based on its capacity to handle the number of I/O points needed, as well as special functions such as proportional, integral, derivative control and data handling. Required capabilities like extensive communications and high-speed control should be carefully evaluated, as these are often the main factors driving controller selection.

Discrete and analog inputs and outputs connect the controller to the machine sensors and actuators. These signals can originate in the main control panel through a terminal strip with wiring to field devices, but a distributed I/O architecture is often a better solution. Distributed I/O reduces wiring by moving the input or output point closer to the field device, and by multiplexing multiple I/O signals over a single cable running from the remote I/O component to the control panel.

For distributed I/O at a smaller scale, IO-Link is a point-to-point serial communication protocol where an IO-Link-enabled device connects to an IO-Link master module. This protocol communicates data from a sensor or actuator directly to a machine controller. It adds more context to the discrete or analog data by delivering diagnostics and detailed device status to the controller.

Communication systems

Another important part of machine control now and for the future is extensive communication capability. It is a good practice to have multiple Ethernet and serial ports available to integrate to a variety of equipment, computers, HMIs, and business and enterprise systems (figure 3).

Multiple high-speed Ethernet ports ensure responsive HMI communication, as well as peer-to-peer and business system networking. Support of industrial Ethernet protocols, including EtherNet/IP and Modbus TCP/IP, is also important for scanner/client and adapter/server connections. These Ethernet connections enable outgoing email, webserver, and remote access communication functions-all important options for machine control.

Machine control often benefits from the availability of legacy communication methods, such as serial RS-232 and RS-485. Modern controllers often also include USB and MicroSD communication and storage options.

A big part of machine control communication is cybersecurity. Consider a layered defense where protection includes remote functions that are only enabled as part of the hardware configuration. For further protection, all tags should be protected from remote access unless the tag is individually enabled for that purpose.



Factory Auto Mar/Apr fig 3
Figure 3. In addition to the multiple communication ports on this BRX controller, additional ports are added using a STRIDE Industrial Ethernet switch and a GS drive serial-to-Ethernet adapter.



Human-machine interface

The HMI shows vital information about machine conditions using graphical and textual views. HMIs can be in the form of touch panels, text panels, message displays, or industrial monitors. They are used for monitoring, control, status reporting, and many other functions.

The purpose of the HMI must be clearly defined. Some machines may only need a fault message display with few control functions. Other machines may demand a detailed view of machine status, access to system parameters, and recipe functionality. Clearly defining the need of the machine will help determine HMI size and capabilities, and this should be done early in the design process.

HMIs can also act as data hubs by connecting to multiple networked devices. In some machine control applications, multiple protocols may be used, and often HMIs can be used for protocol conversion. This functionality can be used to exchange data, such as status and set points, among different controllers and other smart devices.

Some HMIs can also send data to the cloud or enable remote access functionality through the Internet, given proper user name and password authentication.

Work together

Machine automation systems consist of multiple subsystems and components to provide the required power distribution, safety, and real-time control. Each of these subsystems and components must work together, and many are often networked to each other via either hardwiring, or increasingly via digital communication links. Careful design, selection, integration, and testing will ensure the automation system performs as required, both initially and throughout the life cycle of the machine. 

 
 subscribe now jpeg

Fast Forward

  • Power needs to be distributed to a machine’s motors, drives, controllers, and other components.
  • The machine’s safety system must remove motion-causing energy when called upon, including both electrical and fluid power.
  • It is a good practice to have multiple Ethernet and serial ports available to integrate to a variety of equipment, computers, HMIs, and business and enterprise systems.
 

About the Author

Chip McDaniel works in technical marketing for AutomationDirect and is a graduate of Georgia Tech. His 33 years of experience in the industrial automation field include designing, building, and commissioning multi-axis servo systems, as well as marketing a wide range of automation products.

 

Reader Feedback

We want to hear from you! Please send us your comments and questions about this topic to InTechPlus@isa.org.