01 March 2005
Is it time to replace PID?
Applying model-predictive control at the single-loop level may yield the next big leap in performance gains.
By Don Morrison
For more than 70 years, proportional-integral-derivative (PID) control has reigned as the industrial standard, and for good reason: it's simple, fast, versatile, flexible, and such a sensible design that the underlying algorithm hasn't changed one bit in all these years.
Today, more than 99% of all single regulatory loops are configured for PID, and until recently, most engineers and instrumentation specialists considered the alternatives too complex and CPU-expensive for widespread use.
Several factors have created a perfect environment for PID replacement:
- The evolution of control systems from pneumatics to DCS to process knowledge systems
- The convergence of hardware and software technologies
- Wider industry acceptance of advanced control technologies
Now, a next-generation algorithm has appeared on the scene—one that enables model-predictive control at the single-loop level with comparable CPU and memory requirements.
Perhaps it's time to consider what was previously unthinkable—replacing PID.
PID in reality
It's not that PID is bad. However, it does have its weaknesses:
- PID controls have difficulty handling process delays, nonlinear processes, and noisy process signals. This leads to suboptimal control and increased tuning effort.
- PID is not as robust as alternatives, often delivering higher process variability.
- PID tuning is not easy to handle. Effective tuning requires experience, extensive training, and an investment in tuning software.
- PID transfers process signal noise directly to its controller output. This accelerates valve wear and increases energy usage.
These weaknesses add up over time, with the net impact being PID use may actually increase process variability, decrease production and product quality, and ultimately increase operating and maintenance costs.
Because of the widespread use of PID—and the technology's inherent weaknesses—regulatory controls remain one of the last frontiers for pushing performance further. Improvements at the regulatory control level can translate into significant benefits that compound upwards through the process. Single loop controls are the ultimate enablers of business agility and responsiveness. They contribute to operational and equipment safety and are the key means—either directly or indirectly—of implementing environmental control. Furthermore, multivariable control and site-wide optimization ultimately take place by leveraging single-loop controls.
Loop management pays
Industry surveys find that better regulatory control performance typically represents an opportunity of 1% to 4% of plant production. Results at individual plants support this:
- Better management of regulatory controls at specialty chemicals plant resulted in increased refrigerant production valued at $1.7 million per year.
- Adjustments to four regulatory controls on a hydrocracker 444 process resulted in 2.1% feed rate increase valued at $300,000 per year.
- Reduced variability of crude furnace pass temperatures allowed the use of higher crude temperatures during operation. An independent audit found the resulting product upgrade worth $200,000 per year.
The source of these returns becomes clear if you consider some of the key facts about the performance of PID-controlled loops, which make up nearly all plant control loops:
- Fifty percent of standard control loops display undesirable characteristics.
- Thirty-seven percent of plant control loops need retuning once per year or more.
- Of the 37% retuned, only 22% perform better.
These numbers explain why tuning software, services, and valve maintenance is such a big business. However, they don't address the source of the problem—the PID technology itself. Changing the underlying technology can eliminate most of the PID-related control tuning software and services, while minimizing valve maintenance requirements.
Controlling the future
Hockey great Wayne Gretzky once said, "I skate to where the puck is going to be, not where it has been." Extrapolating this illustrates the value of replacing PID with model predictive control at the loop level. One can control the process based on where it is, where it has been, and where it's going.
A new, patented algorithm makes this type of single-input/single-output, model predictive control, possible at the regulatory control level. A solution built on this algorithm overcomes the weaknesses of PID, with memory and CPU requirements comparable to PID.
The PID algorithm is shortsighted. It has no "knowledge" of the system beyond its tuning constants. Only the present is of concern—where the process may go in the future isn't a consideration.
Model predictive control (MPC) looks at the system holistically. First, based on past and current behavior, it predicts where the system will go if no adjustments should happen. The second step in MPC problem resolution is to adjust the bias between what the algorithm predicted would happen at the last execution cycle and what really happened. Finally, the MPC algorithm calculates the necessary control element movement—current move and future move plan to bring the controlled variable to its objective.
Model predictive control—first
Model predictive control—next
Model predictive control—finally
A matter of perspective
Model predictive control works about the same as PID on loops where dead time is the dominating influence. On loops dominated by lags, PID is much better when load upsets occur. Model predictive is better on set point changes, assuming the software exactly knows the process model. However, in the process industries, it is usually the response to load upsets that is the more important.
—John Gerry, president of ExperTune and holder of ISA's Douglas H. Annin Award, for an outstanding achievement in the design or development of components of an automatic control system.
A full suite of tools is available to assist the user in applying the PID-replacement from start to finish. This MPC tool is for those who maintain the system on a day-to-day basis. It even provides a menu-driven interface that walks the control novice through the following tasks:
On-the-fly conversion from PID
Control loop diagnostics, including loop performance and valve diagnostics
Wizard-style tools for MPC development, testing, and deployment
Once deployed, this MPC package continues to provide advantages including:
Single handle for algorithm tuning, more or less aggressive
On-the-fly switching between tight (setpoint) and loose (range or surge) control
Optional configuration for economic optimization—maximize/minimize within a range
Steady-state predictive alarming provides notification of a problem before it actually occurs
Easy integration with sampled analyzers
Gain scheduling for minor process nonlinearities
A replacement strategy
With the right PID replacement strategy, a plant can reap performance gains. These could include increased returns of $100,000 per year on critical loops because of tighter control and less oscillation, increased throughput of 1-4 % and increased plant efficiency of 3-5 %.
When investigating PID replacement at the loop level, consider using these questions to evaluate the available solutions:
Are the CPU and memory requirements comparable to PID?
Does it enable better, more flexible control performance?
Does it reduce valve travel?
Is it easier to tune?
Does it enable the replacement of all loops with little impact on the controller?
Does it provide tools that enable technicians to use the technology easily and quickly?
Does it provide optimal control based on field-proven technology?
Does it provide direct PID conversion that is transparent to the user?
Does it provide upfront diagnosis of valve problems?
Does it automatically identify a model via a regulatory control test?
When one can answer yes to these questions, an appropriate solution for replacing PID is close.
Behind the byline
Don Morrison has a chemical engineering degree and experience in optimization engineering in the refining and petrochemical industry. He works as a manager at Honeywell Process Solutions. There are tens and hundreds of model predictive control software packages available in the automation marketplace.
Return to Previous Page